Gravel Calculator

Enter the area and depth to get the volume, weight and number of bags of gravel, crushed stone, sand, topsoil or mulch, with an allowance for compaction and waste.

Free · No sign-up · Runs in your browser

How to use the gravel calculator

Ordering gravel, crushed stone, sand, topsoil or mulch comes down to the same two questions: how much space are you filling, and how does the supplier sell the material? Landscape suppliers sell by the cubic yard or cubic metre, quarries and builders' merchants often sell by the ton or tonne, and garden centres sell bags. This calculator works out the volume from your area and depth, adds an allowance, and converts it into all three.

  1. Choose units. US mode takes feet and inches and returns cubic yards and US (short) tons. Metric mode takes metres and millimetres and returns cubic metres and tonnes.
  2. Pick the shape. Use a rectangle for paths, patios and driveways, a circle for tree rings and round beds, or enter a known area if you have measured it from a plan. Split odd shapes into pieces and add them up, or get the total from the square footage calculator.
  3. Enter the depth of the finished layer.
  4. Choose the material. Each preset loads a typical density, which you can overwrite with your supplier's figure.
  5. Set the extra percentage for compaction and waste, and the bag size if you are buying bags.

Gravel volume and weight formulas

Area = length × width (rectangle) or π × (diameter ÷ 2)² (circle)
Volume = area × depth × (1 + extra %)
Cubic yards = cubic feet ÷ 27 · 1 yd³ = 0.7646 m³
Weight (tonnes) = volume (m³) × density (t/m³) · 1 tonne = 1.1023 US tons
Bags = ⌈volume ÷ bag size⌉

Keep the depth and the area in the same unit before multiplying: 3 in is 0.25 ft and 75 mm is 0.075 m. Forgetting that step is the most common reason a gravel order comes out twelve times too large.

MaterialTypical density (estimate)Per cubic yard (estimate)
Crushed stone / gravel1.5–1.7 t/m³1.3–1.4 US tons
Pea gravel1.4–1.6 t/m³1.2–1.35 US tons
Crushed base (loose)1.7–1.9 t/m³1.4–1.6 US tons
Dry sand1.5–1.7 t/m³1.3–1.4 US tons
Topsoil1.1–1.4 t/m³0.9–1.2 US tons
Mulch / bark0.3–0.5 t/m³500–800 lb

Densities vary with rock type, grading and moisture. They are planning figures, not supplier data.

Worked examples

A gravel garden path

A path 20 ft long and 4 ft wide at 3 in deep holds 80 × 0.25 = 20 ft³, or 0.74 yd³. With 10% extra that is 0.81 yd³ (22 ft³). At 1.6 t/m³ crushed stone weighs about 1.1 US tons, or 44 bags of 0.5 ft³. One ton of the same stone covers about 80 ft² at 3 in.

A metric driveway sub-base

A 6 × 3 m parking pad with a 100 mm crushed base needs 18 × 0.1 = 1.8 m³ of compacted stone. Adding 15% for compaction brings the loose order to 2.07 m³, which at about 1.8 t/m³ is roughly 3.7 tonnes. The surface gravel goes on top as a separate layer, so run the calculator again for it.

Mulch around a tree

A mulch ring 8 ft across at 3 in deep covers π × 4² = 50.3 ft² and holds 12.6 ft³, or 0.47 yd³. In 2 ft³ bags that is 7 bags, or 7 with 10% extra as well, since 13.8 ft³ still fits in 7 bags. At about 0.4 t/m³ the whole ring weighs only around 140 kg (310 lb).

Who this calculator helps

  • Landscape architects and garden designers scheduling hard and soft landscape materials for a planting or paving plan.
  • Architects putting early quantities on site works, driveways, drainage trenches and sub-bases.
  • Contractors and landscapers turning a site measure into a delivery order in yards, tons or bulk bags.
  • Homeowners pricing a path, patio base, play area or new beds before ordering.
  • Students learning how volume, density and compaction tie together in site work.

Practical tips

  • Ask the supplier whether they sell by loose volume or by weight, and use their density if they give one.
  • Lay a geotextile under paths and driveways to keep the stone from sinking into the subsoil.
  • Compact crushed base in layers of about 75–100 mm (3–4 in); thick single lifts don't compact well.
  • Check slopes and falls on paths and drives with the slope calculator, and price concrete edging or footings with the concrete calculator.
  • Check the truck or trailer limit before ordering by weight: a small trailer often can't carry a full ton.

Want to see the gravel garden before it goes in? Try the new layout on a photo of the site with Landscape.

From numbers to pictures

See the space before it's built.

Once the plan works on paper, BasedFrame turns a sketch, a massing model or a site photo into a photoreal render in seconds. Try Sketch to Render or Room Redesign with free credits.

Try BasedFrame free

FAQ

Gravel Calculator FAQ

How much gravel do I need?

Multiply the area by the depth to get the volume, then convert it to cubic yards or cubic metres. A 20 × 4 ft path at 3 in deep is 80 ft² × 0.25 ft = 20 ft³, or 0.74 yd³. Multiply by the material density to get the weight to order: at about 1.6 t/m³ (2,700 lb/yd³) that path needs roughly 1 US ton of crushed stone, before any allowance for compaction or waste.

How many tons are in a cubic yard of gravel?

Most gravel and crushed stone weighs about 1.3 to 1.5 US tons per cubic yard (roughly 1.5 to 1.8 tonnes per cubic metre), depending on the rock, the grading and how wet it is. The calculator uses 1.6 t/m³ (about 1.35 tons/yd³) for crushed stone as an estimate; ask your supplier for the figure they sell by, and enter it as a custom density.

How many square feet does a ton of gravel cover?

At 1.35 tons per cubic yard, one ton is about 20 ft³ of gravel. Spread 2 in deep it covers about 120 ft², at 3 in about 80 ft² and at 4 in about 60 ft². The calculator shows the coverage per ton (or tonne) for the depth you enter.

How deep should gravel be?

As rough guides, decorative gravel and garden paths are often laid 2–3 in (50–75 mm) deep over a compacted sub-base, and gravel driveways often use 4–6 in (100–150 mm) or more of compacted crushed base under a 2–3 in top layer. Heavier traffic and soft ground need more. These are typical ranges, not a pavement design.

How much extra should I add for compaction?

Loose crushed base settles when it is rolled or plate-compacted, so suppliers and contractors commonly add around 10–20% to the loose volume for a compacted layer, plus a little for uneven ground and spillage. Decorative gravel and mulch that are not compacted usually need only 5–10% extra.

How many bags of gravel make a cubic yard?

A cubic yard is 27 ft³, so it takes 54 bags of 0.5 ft³ or 27 bags of 1 ft³. Bulk delivery is usually far cheaper once you need more than about half a cubic yard, but bags are handy for small beds, pots and places a truck can't reach.

Can I use this for mulch, topsoil and sand?

Yes. The volume is the same calculation; only the density changes. Mulch is light (roughly 0.3–0.5 t/m³), topsoil is around 1.1–1.4 t/m³ depending on moisture, and dry sand is around 1.5–1.7 t/m³. Mulch and topsoil are normally sold by volume, gravel and sand often by weight.

How accurate are the weights?

They are estimates. Density changes with the rock type, particle size, moisture and how the load is measured, so a supplier's ton of one product may not match another's. Use the volume as the firm number and treat the weight as a guide for ordering and for checking truck or trailer limits.

Keep exploring

More free tools for architects

Turn any listing
into rooms that sell

Start with a Zillow link or a single photo. Redesign, stage, relight and walk buyers through every room, ready to list today.